// --------------------------------------------------------------------------------------------------------------------------------- // Configuration for OnStep SmartWebServer Add-on /* * For more information on setting this addon up see https://onstep.groups.io/g/main/wiki/7119 * and join the OnStep Groups.io at https://groups.io/g/onstep * * *** Read the compiler warnings and errors, they are there to help guard against invalid configurations *** */ // --------------------------------------------------------------------------------------------------------------------------------- // ADJUST THE FOLLOWING TO CONFIGURE YOUR ADD-ON'S FEATURES ------------------------------------------------------------------------ // <-Req'd = always must set, <-Often = usually must set, Option = optional, Adjust = adjust as req'd, Infreq = infrequently changed // For Wifi successful startup an AP will appear with an SSID of "ONSTEP", after connecting: the web-site is at "192.168.0.1" and // the cmd channel is at "192.168.0.1:9999". If locked out selecting "Erase Flash: All Flash Contents" from the Arduino Tools menu // before uploading/flashing again can help restore access to the ESP8266. // Parameter Name Value Default Notes Hint // OPERATIONAL MODE ---------------------------------------------------------------------------------------------------------------- #define OPERATIONAL_MODE WIFI // WIFI, Or use ETHERNET_W5100 or ETHERNET_W5500 <-Req'd // SERIAL PORTS -------------------------------------------------------------------------------------------------------------------- #define SERIAL_BAUD_DEFAULT 9600 // 9600, Common baud rates for this parameter are 9600,19200,57600,115200,etc. Infreq // The OnStep serial port this is wired to must use the same rate above. #define SERIAL_BAUD 115200 // 115200, Or use 19200,57600,115200,230400,460800 (not all devices support > 115200) // (OnStep and here.) Automatically uses 19200 if talking to a Mega2560 OnStep. #define SERIAL_SWAP AUTO // AUTO, Automatic check both, ON for swapped port or OFF for default port only. Infreq // this option is ignored in ETHERNET modes // STATUS LED ---------------------------------------------------------------------------------------------------------------------- #define LED_STATUS ON // ON, Enable LED flashes while connecting then steady once connected. Infreq // DISPLAY ------------------------------------------------------------------------------------------------------------------------- #define DISPLAY_WEATHER ON // OFF, ON ambient conditions in locale default units. Option #define DISPLAY_INTERNAL_TEMPERATURE ON // OFF, ON internal MCU temp. in locale default units. Option #define DISPLAY_LANGUAGE L_en // L_en, English. Or L_ce, L_de, L_en, L_us, L_es two letter country code. Adjust #define DISPLAY_WIFI_SIGNAL_STRENGTH ON // ON, Wireless signal strength reported via web interface. OFF otherwise. Option #define DISPLAY_SERVO_MONITOR OFF // OFF, ON to display the servo monitor for OnStepX servos (any axis.) Option #define DISPLAY_SERVO_ORIGIN_CONTROLS OFF // OFF, ON to display control to set the absolute encoder origin for servos. Option #define DISPLAY_RESET_CONTROLS OFF // OFF, ON allows reset if supported, FWU for STM32 firmware upload pin HIGH. Option #define DISPLAY_SPECIAL_CHARS ON // ON, For standard ASCII special symbols (compatibility.) Infreq #define DISPLAY_ADVANCED_CHARS ON // ON, For standard "RA/Dec" instead of symbols. Infreq #define DISPLAY_HIGH_PRECISION_COORDS OFF // OFF, ON for high precision coordinate display on status page. Infreq // DRIVE CONFIGURATION ------------------------------------------------------------------------------------------------------------- #define DRIVE_CONFIGURATION ON // ON, to display/modify mount, rotator, focuser settings Option #define DRIVE_MAIN_AXES_MICROSTEPS ON // ON, to display Axis1/2 Microsteps if available. Option #define DRIVE_MAIN_AXES_CURRENT ON // ON, to display Axis1/2 IRUN if available. Option #define DRIVE_MAIN_AXES_REVERSE ON // ON, to display Axis1/2 Reverse if available. Option // COMMAND SERVER CHANNELS --------------------------------------------------------------------------------------------------------- #define COMMAND_SERVER BOTH // BOTH, for STANDARD (port 9999) and PERSISTENT (ports 9996 to 9998) // or disable with OFF // ENCODER SUPPORT ----------------------------------------------------------------------------------------------------------------- // Some of these settings are stored in NV (EEPROM) as the default values when first uploaded. Later changes below may be // ignored unless NV is wiped or you configure to revert to the defaults again at runtime. #define ENC_AUTO_SYNC_DEFAULT ON // ON, Automatically sync Encoders to OnStep. Option #define ENC_AUTO_SYNC_MEMORY OFF // OFF, ON Remember automatic sync setting across power cycles. Option #define ENC_SYNC_DURING_GOTO ON // OFF, ON high resolution encoders correct pointing even for gotos. Option #define AXIS1_ENCODER_TICKS_DEG 22.22222 // 22.222, n, (ticks/degree.) Encoder ticks per degree. Adjust #define AXIS1_ENCODER_REVERSE OFF // OFF, ON to reverse the count direction. Option #define AXIS1_ENCODER_DIFF_LIMIT_TO 300 // 300, n, (arcsec.) Minimum diff. between encoder/OnStep for sync. to OnStep Adjust #define AXIS1_ENCODER_DIFF_LIMIT_FROM OFF // OFF, n, (arcsec.) Maximum diff. between encoder/OnStep for sync. from OnStep Adjust #define AXIS1_ENCODER OFF // OFF, AB, AB_ESP32, CW_CCW, PULSE_DIR, AS37_H39B_B. RA/Azm (A/MA) & (B/SLO.) Option // for absolute encoders. #define AXIS2_ENCODER_TICKS_DEG 22.22222 // 22.222, n, (ticks/degree.) Encoder ticks per degree. Adjust #define AXIS2_ENCODER_REVERSE OFF // OFF, ON to reverse the count direction. Option #define AXIS2_ENCODER_DIFF_LIMIT_TO 300 // 300, n, (arcsec.) Minimum diff. between encoder/OnStep for sync. to OnStep. Adjust #define AXIS2_ENCODER_DIFF_LIMIT_FROM OFF // OFF, n, (arcsec.) Maximum diff. between encoder/OnStep for sync. from OnStep. Adjust #define AXIS2_ENCODER OFF // OFF, AB, AB_ESP32, CW_CCW, PULSE_DIR, AS37_H39B_B. Dec/Alt (A/MA) & (B/SLO.) Option // for absolute encoders. // THAT'S IT FOR USER CONFIGURATION! // ------------------------------------------------------------------------------- #include "Extended.config.h"